« previous next »
Pages: [1] 2  All   Go Down

Author Topic: boost then bang  (Read 18920 times)

0 Members and 1 Guest are viewing this topic.

Offline caranx

  • Calibra Rookie
  • Posts: 62
  • Respect 0
  • Gender: Male
    • Cally 16v Turbo
boost then bang
« on: October 04, 2018, 19:06:54 PM »
hello guys
please i need a bit of advice , so finally got new radiator in and brake master cylinder in , so now i could test,
put it on the high way all going well hitting small boost but running  really nice ,but then i pushed it a little about .8 or so not sure........
loud sound ( sounded like wast-gate dump but loud then she wouldent go ...as if a boost pipe is off , stopped and cheaked all is on , so i turned around and went back home , she wont idle nice, kinda lumpy  bit low , wont climb in the reves , she just starts spluttering ,

im at a loss atm , i thought i was winning , cant see any oil leaks everything lo0oks good .....just she wont go now
 dose anybody have any ideas? please
Logged

Offline Faur Sergiu

  • Calibra Rookie
  • Posts: 102
  • Respect 0
  • Gender: Male
    • Cally 16v Turbo
Re: boost then bang
« Reply #1 on: October 04, 2018, 20:26:07 PM »
 Hi do you still have boost? Check the pipes or the intercooler
Logged

Offline caranx

  • Calibra Rookie
  • Posts: 62
  • Respect 0
  • Gender: Male
    • Cally 16v Turbo
Re: boost then bang
« Reply #2 on: October 04, 2018, 21:28:40 PM »
i am going to do a boost leak cheak in the morning , its a bit dark out ,just bummed man i had just got her out first road test ...i feel like an id10T , thank you  for the reply
Logged

Offline caranx

  • Calibra Rookie
  • Posts: 62
  • Respect 0
  • Gender: Male
    • Cally 16v Turbo
Re: boost then bang
« Reply #3 on: October 06, 2018, 00:23:24 AM »
so it was too late and dark to start looking for what happened and in my panic \ freak out ...lol i put message up here for help  :P

So next day after  work with day light on mi side , i did a boost leak test it was the first silicone join after the turbo one with a bend close to turbo outlet , clamp failed ... and im assuming  she was getting in clean air after maf and is why she ran poorly .

im very relived it wasent worse , i have tred looking for this eds chip , dose any body have a link ?
Logged

Offline Faur Sergiu

  • Calibra Rookie
  • Posts: 102
  • Respect 0
  • Gender: Male
    • Cally 16v Turbo
Re: boost then bang
« Reply #4 on: October 06, 2018, 09:11:52 AM »
https://www.eds-motorsport.de/?cat=c2879_Softwareoptimierung-Benzin-Benzin-2879.html and an advice go for c20xe radiator 82c thermostat, a FMIC bigger injectors 470 cc. Good luck mate
Logged

Offline caranx

  • Calibra Rookie
  • Posts: 62
  • Respect 0
  • Gender: Male
    • Cally 16v Turbo
Re: boost then bang
« Reply #5 on: October 06, 2018, 20:15:37 PM »
thank you very much ,
 i have done quiet a bit of work getting car reliable , got fmic and saab inectors, bigger down pipe

 iv also sorted the boost  pipes out with boost controller gait set to 0  shes running up to 1,2bar  with a bit of surge ,
so iv got sum work still to do .
im hopping  the eds will help with sorting mi fuling out
 , otherwise shes pulling strong, have awsume week end mate  ;D
Logged

Offline Faur Sergiu

  • Calibra Rookie
  • Posts: 102
  • Respect 0
  • Gender: Male
    • Cally 16v Turbo
Re: boost then bang
« Reply #6 on: October 07, 2018, 09:08:49 AM »
Change the saab injectors fast with 470 cc if you want phase 2 or 3 you will melt your pistons , I use them and got 1 piston melted go for bigger injectors 470 cc with 3 bar fuel pressure
Logged

Offline Faur Sergiu

  • Calibra Rookie
  • Posts: 102
  • Respect 0
  • Gender: Male
    • Cally 16v Turbo
Re: boost then bang
« Reply #7 on: October 07, 2018, 09:14:14 AM »
Forgot for eds phase 2 you need 1.05 bar boost(continous) and for phase 3 eds 1.15 boost continous and 1.5 overboost .
Im running eds 3. Need to change injectors and and both camshaft from c20xe . Change the colant hooses with silicone ones from do88.se . Cheers and good luck mate
Logged

Offline caranx

  • Calibra Rookie
  • Posts: 62
  • Respect 0
  • Gender: Male
    • Cally 16v Turbo
Re: boost then bang
« Reply #8 on: October 07, 2018, 10:55:29 AM »
thank you for that i really appreciate the advice i will start looking now for injectors
i installed the innovate scg1 boost controller with AFR , works really well .

im not even using the boost controller function, just the boost protection.
 iv capped it at 1.5bar cos i dont waana kill it unnecessary  till its running right   .i have important question ??what is safe boost for k16 ....
she is pulling really well i was chacing an AMG this morning on the high way , i was with him the whole way he wasent getting away  but  ...BUT   the boost comes on it goes right up till it hits the limit and the  controlles cuts boost
im a little werie to turn boost limit off and see what happens , fule is rich at the moment on the stock ecu map so i should be safe there , engine is stock , turbo is recently full service , 200x600fmic, saab reds , bigger down piepe and staright pipe no boxs ( sounds like a monster ) , so not much ,   what is safe boost for k16?

Logged

Offline Faur Sergiu

  • Calibra Rookie
  • Posts: 102
  • Respect 0
  • Gender: Male
    • Cally 16v Turbo
Re: boost then bang
« Reply #9 on: October 07, 2018, 11:56:25 AM »
The max safe boost for k16 is 1.1 bar continous and 1.5 bar overboost 280-300hp . How much hp do you have now?
Logged

Offline Faur Sergiu

  • Calibra Rookie
  • Posts: 102
  • Respect 0
  • Gender: Male
    • Cally 16v Turbo
Re: boost then bang
« Reply #10 on: October 07, 2018, 11:58:54 AM »
At 1.5 bar continuous you will kill your turbo , you have stock fuel pressure regulator ?
Logged

Offline Faur Sergiu

  • Calibra Rookie
  • Posts: 102
  • Respect 0
  • Gender: Male
    • Cally 16v Turbo
Re: boost then bang
« Reply #11 on: October 07, 2018, 12:06:39 PM »
You need new injectors if you go for phase 2 or 3 if is stock you don't need to change them if you want 280hp or more go for bigger injector 470cc cheers and good luck
Logged

Offline caranx

  • Calibra Rookie
  • Posts: 62
  • Respect 0
  • Gender: Male
    • Cally 16v Turbo
Re: boost then bang
« Reply #12 on: October 07, 2018, 15:15:30 PM »
im running 3.5 bar fuel pressure atm, and as im thinking about it i need to look at why the wastgate is not working .... seem to me like is jammed shut and the car is hitting the boost limit  on the over boost protection , i proppably whould have blown that motor by now if it wasent for that scg-1
Logged

Offline caranx

  • Calibra Rookie
  • Posts: 62
  • Respect 0
  • Gender: Male
    • Cally 16v Turbo
Re: boost then bang
« Reply #13 on: October 07, 2018, 15:26:16 PM »
i am looking at either a gt25 or gt28 kinda set up not too crazy but still very quick, so the bigger injectors  will be a must i am aming for around 260 to 300 bhp ,  keep the set up reliable for longevity  , i dont really want to go stand alone management so if i can keep it all sanded like , that will be cool , im trying to learn about ecu programming , the eds chip just seems to be the easyist option right now 
Logged

Offline Faur Sergiu

  • Calibra Rookie
  • Posts: 102
  • Respect 0
  • Gender: Male
    • Cally 16v Turbo
Re: boost then bang
« Reply #14 on: October 07, 2018, 15:58:20 PM »
EDS its a good option . Im runing eds ph 3 . K16 its good for ph 3 you don't need to change the turbo for ph 3 and eds has 5 setups for power to set you can switch at any time betwin 170 204 260 280 and 310 hp by power wheel that is instaled into your car thats controlls the boost electronical from 0.3 to 1.1 bar boost
Logged
Pages: [1] 2  All   Go Up
« previous next »